Other Configuration Options
Handling Signals
If your program contains a signal handler routine, you may need to adjust the way TotalView handles signals. The following table shows how TotalView handles UNIX signals by default:
 
Signals Passed Back to Your Program
Signals Treated as Errors
SIGHUP
SIGIO
SIGILL
SIGPIPE
SIGINT
SIGIO
SIGTRAP
SIGTERM
SIGQUIT
SIGPROF
SIGIOT
SIGTSTP
SIGKILL
SIGWINCH
SIGEMT
SIGTTIN
SIGALRM
SIGLOST
SIGFPE
SIGTTOU
SIGURG
SIGUSR1
SIGBUS
SIGXCPU
SIGCONT
SIGUSR2
SIGSEGV
SIGXFSZ
SIGCHLD
 
SIGSYS
 
NOTE >> TotalView uses the SIGTRAP and SIGSTOP signals internally. If a process receives either of these signals, TotalView neither stops the process with an error nor passes the signal back to your program. You cannot alter the way TotalView uses these signals.
On some systems, hardware registers affect how TotalView and your program handle signals such as SIGFPE. For more information, see Interpreting the Status and Control Registers” and theArchitectures” chapter in the TotalView Reference Guide.
NOTE >> On an SGI computer, setting the TRAP_FPE environment variable to any value indicates that your program traps underflow errors. If you set this variable, however, you also need to use the controls in the File > Signals Dialog Box to indicate what TotalView should do with SIGFPE errors. (In most cases, you set SIGFPE to Resend.)
You can change the signal handling mode using the File > Signals command, Figure 48
Figure 48 – File > Signals Dialog Box
 
The signal names and numbers that TotalView displays are platform-specific. That is, what you see in this box depends on the computer and operating system in which your program is executing.
You can change the default way in which TotalView handles a signal by setting the TV::signal_handling_mode variable in a .tvdrc startup file.
When your program receives a signal, TotalView stops all related processes. If you don’t want this behavior, clear the Stop control group on error signal check box on the Options Page of the File > Preferences Dialog Box.
CLI: dset TV::warn_step_throw
When your program encounters an error signal, TotalView opens or raises the Process Window. Clearing the Open process window on error signal check box, also found on the Options Page in the File > Preferences Dialog Box, tells TotalView not to open or raise windows.
CLI: dset TV::GUI::pop_on_error
If processes in a multi-process program encounter an error, TotalView only opens a Process Window for the first process that encounters an error. (If it did it for all of them, TotalView would quickly fill up your screen with Process Windows.)
If you select the Open process window at breakpoint check box on the File > Preferences Action Points Page, TotalView opens or raises the Process Window when your program reaches a breakpoint.
CLI: dset TV::GUI::pop_at_breakpoint
Make your changes by selecting one of the radio buttons described in the following table.
Button
Description
Error
Stops the process, places it in the error state, and displays an error in the title bar of the Process Window. If you have also selected the Stop control group on error signal check box, TotalView also stops all related processes. Select this button for severe error conditions, such as SIGSEGV and SIGBUS.
Stop
Stops the process and places it in the stopped state. Select this button if you want TotalView to handle this signal as it would a SIGSTOP signal.
Resend
Sends the signal back to the process. This setting lets you test your program’s signal handling routines. TotalView sets the SIGKILL and SIGHUP signals to Resend since most programs have handlers to handle program termination.
Ignore
Discards the signal and continues the process. The process does not know that something raised a signal.
NOTE >> Do not use Ignore for fatal signals such as SIGSEGV and SIGBUS. If you do, TotalView can get caught in a signal/resignal loop with your program; the signal immediately reoccurs because the failing instruction repeatedly re-executes.
 
RELATED TOPICS 
 
Thread continuation signal command
Thread > Continuation Signal in the in-product Help
The TV::signal_handling_mode variable in a .tvdrc startup file
Command-Line Options” in the TotalView Reference Guide
TotalView preferences
The File > Preferences dialog in the in-product Help and Setting Preferences”